CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019Printed In USAOp e r a t O r ’s Ma n u a lSafe Operation Practices • Set-Up • Operation • Ma
Attaching the Negative Battery CableNOTE: negative battery terminal is marked Neg. (–).The posit
Adjusting the Seat To adjust the position of the seat, pull up and hold the seat adjustment lever. Slide the seat forward or rearward to the desired p
Systems Indicator MonitorBrake PedalDrive PedalDeck Lift LeverCup HolderFuel Tank CapThrottle/Choke ControlIgnition Switch ModuleParking Brake/Cruise
Deck Lift Leverchange the height of the cutting deck. To use, move the lever to t
Fuel Level IndicatorThe Fuel Level Indicator is located on the left side of the tank.PTO /
TO AVOID SERIOUS INJURY OR DEATH• GO UP AND DOWN SLOPES, NOT ACROSS. • AVOID SUDDEN TURNS.• DO NOT OPERATE THE UNIT WHERE IT COULD SLIP OR TIP.• I
Driving The TractorWARNING! Avoid sudden starts, excessive speed and sudden stops. Lightly press the brake pedal to release the parking brake. Mov
Driving On Slopeswhere you may operate the tractor safely.WARNING! Do not mow on inclines
Engaging the PTOMove the Throttle/
Maintenance ScheduleBefore Each useEvery 10 HoursEvery 25 HoursEvery 50 HoursEvery 100 HoursPrior to StoringClean Hood/Dash LouversP PCheck Engine Oi
Customer SupportIf you have difficulty assembling this product or have any questions regarding the controls, operation, or maintenance of this machine
Remove the oil fill cap/ dipstick from the oil
Attach the hose coupler to the water port on your decks 4. surface. See Fig. 6-2.Turn the water on.5.
Leveling the Deck (Side to Side)If the cutting deck appears to be mowing unevenly, a side to side adjustment can be performed. Adjust if necessary as
Steering AdjustmentIf the tractor turns tighter in one direction than the other, or if the ball joints are being replaced due to damage or wear, the s
Cutting Deck RemovalTo remove the cutting deck, proceed as follows:brake.
Continue holding the blade onto the star hub of the spindle, and remove the flange nut and cutting blade. Repeat the previous steps to remove the o
Changing the Timing BeltWARNING! Be sure to shut the engine off, remove ignition key, disconnect the spark plug wire(s) to prevent unintended starting
If the timing belt was installed correctly and the timing arrows were positioned as shown in Fig. 7-6, the cutting blades should be in the positio
BatteryCALIFORNIA PROPOSITION 65 WARNING! Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the St
Problem Cause RemedyEngine fails to start 2. Spark plug wire disconnected. Throttle/C
Important Safe Operation Practices23General OperationRead, understand, and follow all instructions on the machine and in the manual(s) before attem
Component Part Number and Description
which you purchased yo
Notes1133
CALIFORNIA EMISSION CONTROL WARRANTY STATEMENTYOUR WARRANTY RIGHTS AND OBLIGATIONSThe California Air Resources Board and MTD Consumer Group Inc are pl
WARRANTED PARTS:The repair or replacement of any warranted part otherwise eligible for warranty coverage may be excluded from such warranty coverage i
IMPORTANT: To obtain warranty coverage owner must present an original proof of purchase and applicable maintenance records to the servicing dealer. Pl
4 se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sA missing or damaged discharge cover can cause blade contact or th
5se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sChildrenTragic accidents can occur if the operator is not alert to the
6 se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e scomplete stop wi
7se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sSafety SymbolsThis page depicts and describes safety symbols that may a
8 se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sSight and hold this level with a vertical tree...or a corner of a buil
Tractor Set-UpMoving The Tractor Manuallyrelief valve for occasions when it is necessary to
Comments to this Manuals