Cub Cadet 8404 Service Manual Page 233
- Page / 289
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
STEERING SYSTEM
8-23
D615-W02 May-2003
b. Air Bleeding in Steering Hose
• After the engine has stopped, run engine at 2000 ~
2200 rpm, turn steering wheel to the maximum in
left and right and perform relief valve operation five
or six times.
• Turn steering wheel to the maximum in left and right
with 1200 ~ 1500 rpm, while relief valve beep
occurred, disengage (about 1/4 rotation) hose tight-
ening nut to allow air bleeding and then retighten
nut.
Sect. Spec. Tightening torque
Steering cylinder
hose tightening
torque
PT 1/4 46.6 ~ 50.0 N·m
4.8 ~ 5.21 kgf·m
34.4 ~ 37.6 lbf·ft
615W844A
• After assembling split pin, make sure the end is not
fallen.
• Apply support pin and grease nipple with sufficient
grease.
Sect. Spec. Tightening torque
Nut
M18 48.0 ~ 55.9 N·m
4.9 ~ 5.7 kgf·m
35.5 ~ 41.2 lbf·ft
Sealing agent Loctite #572 or equivalent
Connecting port and
hose color
Steering hose assembly
R (White)
Steering hose assembly
(yellow)
Assembly position
Right steering cylinder
Left steering cylinder
• When assembly steering cylinder connector, apply
screw with sealing agent.
• When connecting with steering cylinder hose, make
sure the color and connecting port is correct.
• After assembly steering hose, perform air bleeding.
(1) Split Pin (2) Slotted Nut
www.mymowerparts.com
K&T Saw Shop 606-678-9623 or 606-561-4983
- CONTENTS 3
- 1. TRACTOR VIEW 11
- 2.1 TIGHTENING TORQUE 12
- GENERAL INFORMATION 13
- 3. SPECIFICATIONS 14
- 4. IDENTIFICATION 16
- 5. CAUTION BEFORE REPAIR 17
- 5.6 ELECTRICAL SYSTEM 18
- 5.5 ASBESTOS PARTS 18
- 6. REGULAR CHECK LIST 20
- ENGINE SYSTEM 23
- 1. GENERAL 25
- 1.2 SPECIFICATIONS 26
- 1.3 PERFORMANCE CURVE 27
- 1.4 DIMENSIONS 28
- 1.5. GENERAL WARNING 28
- 2. STRUCTURE AND FUNCTION 29
- CHAPTER 2 8354/8404 30
- 2.2 LUBRICATING SYSTEM 33
- 2.3 COOLING SYSTEM 35
- 2.4 FUEL SYSTEM 37
- 4) To stop engine 43
- 3.1 TROUBLESHOOTING 45
- 3.2 SERVICING SPECIFICATIONS 48
- I. Timing Gear 50
- 1) Fan belt 57
- 1) Engine body 57
- 1) Compression pressure 59
- 2) Valve clearance 60
- 1) Timing Gears and Camshafts 63
- (A) Injection pump 63
- (E) Gear case 64
- (C) Start spring 64
- (D) Fan drive pulley 64
- (G) Idle gear and crank gear 65
- 2) Connecting rod and piston 66
- 12 13111078210 65439 71
- 2) Timing gears and camshafts 73
- 4) Crankshaft 78
- 5) Cylinder bore 81
- 2) Injection nozzle 88
- 1) Injection pump 88
- CHAPTER 3 89
- 1. DISASSEMBLY AND ASSEMBLY 91
- 615W302A 615W303A 615W304A 92
- B. SECOND STAGE 92
- 615W305A 92
- C. THIRD STAGE 93
- 2. CLUTCH 96
- 615W320A 97
- 2.3 TROUBLESHOOTING 98
- 2.4 SPECIFICATION 99
- 2.5 TIGHTENING TORQUE 99
- 2.6 DISASSEMBLY, MAINTENANCE 100
- B. DISASSEMBLY, ASSEMBLY 101
- CHAPTER 3 8354/8404 102
- 615W329A 103
- TRANSMISSION 105
- 1. STRUCTURE 107
- 2. POWER TRANSMISSION 108
- Intermediate Stage 109
- B. Synchro Operation 109
- 1st Stage 109
- Final Stage 110
- Reversing 111
- Power Transmission Flow Chart 111
- Low Speed 112
- High Speed 112
- Power Transmission Flow 112
- A. Power Transmission Flow 114
- CHAPTER 4 8354/8404 116
- 4. PTO CLUTCH 118
- 5. DIFFERENTIAL GEAR 120
- B. Turning a Corner 121
- C. Differential Lock 122
- 6. TROUBLESHOOTING 123
- 7. MAINTENANCE SPECIFICATION 124
- 8. TIGHTENING TORQUE 125
- 9. CLUTCH HOUSING 126
- 11. INTERMEDIATE CASE 141
- Case and Transmission Case) 142
- 12.1 DISASSEMBLY, ASSEMBLY 150
- 12. TRANSMISSION CASE 150
- 615W483A 152
- 615W485A 152
- Pinion Shaft) 154
- D615-W02 May-2003 156
- 12.2 MAINTENANCE 160
- REAR AXLE 165
- 2. TIGHTENING TORQUE 168
- 3. SERVICE SPECIFICATION 169
- 4. DISASSEMBLY, ASSEMBLY 170
- CHAPTER 5 8354/8404 172
- 5. MAINTENANCE 173
- CHAPTER 6 175
- Operational Principle 178
- 3. TROUBLESHOOTING 179
- 4. MAINTENANCE SPECIFICATION 180
- 5. TIGHTENING TORQUE 180
- 6. BRAKE PEDAL 181
- CHAPTER 6 8354/8404 182
- 7. BRAKE CASE 183
- B. Brake Case Disassembly 185
- D. Wear Check of Brake Disc 187
- B. Wear Check of Cam Plate 187
- E. Wear Check of Brake Plate 187
- FRONT AXLE 189
- 2. WHEEL ALIGNMENT 192
- 6.1 CHECK AND ADJUSTMENT 196
- 6. DISASSEMBLY, MAINTENANCE 196
- Rocking Force) 197
- IMPORTANT: 198
- Assembly) 199
- Cylinder Hydraulic Hose) 199
- 8. DISASSEMBLY OF FRONT AXLE 200
- A. DX Bush Assembling Method 201
- CHAPTER 7 8354/8404 202
- 9. MAINTENANCE 206
- A. Types of Adjusting Shim 210
- B. Tooth Contacted Check 210
- STEERING SYSTEM 211
- 1. CHARACTERISTICS 213
- CHAPTER 8 8354/8404 214
- 3. GEAR PUMP 215
- 615W805A 216
- A. Control Valve 217
- B. Metering Device 217
- 5. STEERING CYLINDER 218
- 6. OIL FLOW 219
- 7. TROUBLESHOOTING 221
- 8. DISASSEMBLY, MAINTENANCE 222
- 615W828A 229
- 615W829A 229
- A. Check 231
- HYDRAULIC SYSTEM 235
- 1. HYDRAULIC CIRCUIT DIAGRAM 237
- 2. STRUCTURE 238
- 4. HYDRAULIC PUMP 240
- 5. OIL FILTER 241
- 6. CONTROL VALVE (MLS VALVE) 242
- A. Neutral Phase 243
- B. Delivery Phase 244
- C. Discharge Phase 245
- CHAPTER 9 8354/8404 246
- 8. HYDRAULIC CYLINDER 247
- 9. STRUCTURE AND OPERATION 248
- A. Position Control 249
- (Fig. 225W918A,225W919A) 250
- (Fig. 615W918A,615W919A) 251
- A. Operation principle 253
- B. Circuit diagram 253
- 11. TOP LINK BRACKET DEVICE 254
- 12. TROUBLESHOOTING 255
- 13. MAINTENANCE SPECIFICATION 256
- 14. TIGHTENING TORQUE 258
- 15. DISASSEMBLY, ASSEMBLY 259
- A. DISASSEMBLY, ASSEMBLY 261
- E. Lever Position Setting 270
- ELECTRIC SYSTEM 273
- 1. ELECTRONIC INSTRUMENTATION 275
- CHAPTER 10 8354/8404 276
- ELECTRICAL SYSTEM 277
- 2. TROUBLE SHOOTING 278
- 3. SERVICING SPECIFICATIONS 280
- 4. MECHANISM 281
- 4.2 CHARGING SYSTEM 284
- 4.3 PREHEATING SYSTEM 286
- 4.4 FUSE 287
- 4.5 GAUGE AND SENSORS 288
- 5. MAIN CIRCUIT DIAGRAM 289
Related products and manuals for Tractor Cub Cadet 8404
Tractor Cub Cadet RANGER RZR User Manual
(20 pages)
(20 pages)
Tractor Cub Cadet 431D User Manual
(15 pages)
(15 pages)
Tractor Cub Cadet 435A Operator's Manual
(24 pages)
(24 pages)
Tractor Cub Cadet 431D User Manual
(4 pages)
(4 pages)
Tractor Cub Cadet GT2000 Operator's Manual
(60 pages)
(60 pages)
Tractor Cub Cadet 642 Operator's Manual
(24 pages)
(24 pages)
Tractor Cub Cadet 640 Operator's Manual
(28 pages)
(28 pages)
Tractor Cub Cadet RZT 54 Operator's Manual
(40 pages)
(40 pages)
Tractor Cub Cadet 430A Operator's Manual
(76 pages)
(76 pages)
Tractor Cub Cadet 640 Operator's Manual
(20 pages)
(20 pages)
Tractor Cub Cadet 7284 User Manual
(89 pages)
Tractor Cub Cadet 641 Operator's Manual
(24 pages)
(24 pages)
Tractor Cub Cadet J466 User Manual
(2 pages)
(2 pages)
Tractor Cub Cadet RZT50 Operator's Manual
(44 pages)
(44 pages)
Tractor Cub Cadet GT 2554 Operator's Manual
(60 pages)
(60 pages)
Tractor Cub Cadet GT 2544 Operator's Manual
(60 pages)
(60 pages)
Tractor Cub Cadet J466 Operator's Manual
(32 pages)
(32 pages)
© 2020, manymanuals.com. All rights reserved. | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals