Cub Cadet 8454 Service Manual Page 82
- Page / 334
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
CHAPTER 2 8454
2-60
D569-W02 May-2003
569W2B6A
569W2B5A
(1) Relief Valve Ball (3) Relief Valve Spring
(2) Relief Valve Seat
E. LUBRICATING SYSTEM
a. Checking
(A) Engine oil pressure
1. Remove the oil pressure switch and install adap-
tors and pressure tester.
2. Start the engine and run it until it is warmed up, and
measure the oil pressure both at idling and rated
speed.
3. If the oil pressure is less than the allowable limit,
check the amount of oil, oil filter, oil pump relief
valve, oil passages and oil clearance.
Engine
oil pres-
sure
Factory
spec.
Factory
spec.
Allowable
limit
more than 49 kPa
0.5 kgf/cm
2
7.11 psi
294 ~ 441 kPa
2.5 ~ 4.5 kgf/cm
2
35.6 ~ 64.0 psi
245 kPa
2.5 kgf/cm
2
35.6 psi
At idle
speed
At rated
speed
(B) Oil filter and relief valve
1. Drain the engine oil and remove the oil filter to check
it.
2. Check the relief valve for dirt, and the seat (2) and
ball (1) for damage.
3. If damaged, replace.
4. Check the free length of spring (3).
5. If it is less than the allowable limit, replace it.
(Reference)
Tightening
torque
Oil
pressure
switch
14.7 ~ 19.6 N·m
1.5 ~ 2.0 kgf·m
10.8 ~ 14.5 lbf·ft
Spring free
length
Factory
spec
Allowable
limit
35 mm
1.38 in.
30 mm
1.18 in.
Tightening
torque
Relief
cover
32.4 ~ 36.3 N·m
3.3 ~ 3.7 kgf·m
23.9 ~ 36.8 lbf·ft
NOTE:
• Install the relief valve cover with the mark up.
www.mymowerparts.com
K&T Saw Shop 606-678-9623 or 606-561-4983
- FORM NUMBER 769-00903 1
- CONTENTS 3
- 1. TRACTOR VIEW 11
- 2.1 TIGHTENING TORQUE 12
- GENERAL INFORMATION 13
- 3. SPECIFICATION 14
- 3. SPECIFICATION CON'T 15
- 4. IDENTIFICATION 16
- 5. CAUTION BEFORE REPAIR 17
- 5.6 ELECTRICAL SYSTEM 18
- 5.5 ASBESTOS PARTS 18
- 6. REGULAR CHECK LIST 20
- CHAPTER 2 23
- 1. GENERAL 25
- 1.3 PERFORMANCE CURVE 27
- Sample/td Spec 28
- 2. STRUCTURE AND FUNCTION 29
- 569W211A 30
- 569W210A 30
- 569W209A 30
- F. CAMSHAFT 31
- G. FUEL CAMSHAFT 31
- H. ROCKER ARM ASSEMBLY 31
- CHAPTER 2 8454 32
- 2.2 LUBRICATING SYSTEM 33
- 2.3 COOLING SYSTEM 35
- 2.4 FUEL SYSTEM 37
- 569W231A 39
- 569W232A 39
- E. FUEL INJECTION NOZZLE 41
- 569W239A 43
- 569W240A 43
- 2.5 INTAKE AND EXHAUST SYSTEM 44
- D. TURBOCHARGER (8454) 45
- 3.1 TROUBLESHOOTING 46
- 3.2 SERVICING SPECIFICATIONS 49
- I. Timing Gear 51
- C. COOLING SYSTEM 53
- D. FUEL SYSTEM 53
- A. ENGINE DISASSEMBLED VIEW 55
- 1) Fan belt 57
- 1) Engine body 57
- 2) Solenoid 58
- 1) Compression pressure 59
- 3) Rocker arm assembly 61
- 4) Cylinder head 62
- 5) Valve 62
- 1) Injection pump 63
- 7) Idle gear and crank gear 65
- 569W283A 69
- 569W282A 69
- 569W281A 69
- 12 13111078210 65439 71
- 569W295A 73
- 569W294A 73
- 569W293A 73
- 569W2A1A 75
- 569W2A0A 75
- 569W299A 75
- 569W2A6A 77
- 569W2A5A 77
- 569W2B1A 79
- 569W2B0A 79
- 569W2A9A 79
- 569W2B3A 81
- 569W2B4A 81
- 569W2B6A 82
- 569W2B5A 82
- 569W2B7A 83
- 569W2B8A 83
- 569W2B9A 83
- 569W2C3A 85
- 569W2C4A 85
- 569W2C5A 85
- 569W2C7A 87
- 569W2C8A 87
- 2) Injection nozzle 89
- Nozzle Holder 89
- CHAPTER 3 91
- SPECIAL TOOLS 94
- 3. STRUCTURE AND OPERATION 95
- 3.3 OPERATION 96
- CHAPTER 3 8454 98
- 4.2 SEPARATING ENGINE AND 99
- CLUTCH HOUSING CASE 99
- ASSEMBLY 100
- 5. ADJUSTMENT OF PEDAL 101
- 6. INSPECTION AND REPAIR 102
- 569W318A 103
- 6.6 CLEARANCE BETWEEN CLUTCH 104
- PEDAL SHAFT AND CLUTCH 104
- PEDAL BUSHING 104
- TRANSMISSION SYSTEM 105
- 1. TROUBLESHOOTING 107
- CHAPTER 4 8454 108
- 2. SPECIFICATIONS 110
- 3. STRUCTURE 111
- 3.2 STRUCTURE 112
- 3.3 POWER TRAIN 113
- CHAPTER 4 8454 114
- 3.4 OPERATION 118
- First Stage 119
- Final Stage 120
- 569W418A 122
- 569W417A 122
- Inertial Brake 124
- ASSEMBLING TRANSMISSION 126
- Preparation 1 127
- Preparation 2 127
- Preparation 129
- Shift Levers 131
- Hydraulic Pipes 131
- 5.1 STANDARD TABLE FOR REPAIR 132
- 5.2 TO DISASSEMBLING AND TO 132
- ASSEMBLE 132
- Clutch Ass’y 147
- Clutch Disc, Steel Plate Wear 152
- Thickness of Seal Ring 153
- PTO Clutch Pack 153
- <Rear Axle Section> 154
- 6. DIFFERENTIAL GEAR 159
- 6.2 OPERATION 160
- Differential Gear 161
- Differential Lock 162
- Adjustment of BacKlash 164
- Confirmation of Reaching Up 165
- Side Gear 169
- • Differential Gear Assembly 169
- • Spiral Bevel Gear 170
- • Checking Bearing 171
- • Differential Side Gear 171
- Hub and Spline 172
- FRONT AXLE 175
- 3.2 FRONT WHEEL ALIGNMENT 181
- 3.3 TOE IN ADJUSTMENT 182
- 3.4 DIRECTION CONTROL ANGLE 182
- FOR THE FRONT WHEEL 182
- REAR DIRECTIONS 183
- 4.1 SEPARATING FRONT AXLE 184
- IMPORTANT: 184
- CHAPTER 5 8454 186
- 5.3 BEVEL GEAR CASE AND FRONT 188
- AXLE SUPPORT 188
- 5.4 FRONT AXLE SUPPORT AND 189
- DIFFERENTIAL GEAR CASE 189
- 5.5 FRONT DIFFERENTIAL GEAR 190
- Adjustment of Backlash 192
- 5.6 FRONT BRACKET 193
- 5.7 REAR BRACKET 194
- HYDRAULIC SYSTEM 195
- CHAPTER 6 8454 198
- 1.1 TROUBLESHOOTING 199
- 1.2 SPECIFICATIONS 200
- 1.3 STRUCTURE AND OPERATION 203
- Hydraulic Oil Flow 204
- Drawbar Pull 214
- (Fig. 569W616A,569W617A) 214
- 1.4 PREPARATION STAGE FOR 219
- DISASSEMBLING AND 219
- ASSEMBLING 219
- 1.5 DISASSEMBLING AND 221
- Arm Shaft and Bush 228
- Dimension 229
- Draft Control Lever 230
- 2. PTO CLUTCH VALVE SYSTEM 232
- 2.2 STRUCTURE AND OPERATION 233
- 2.4 TO CHECK AND TO REPAIR 240
- 3. POWER STEERING SYSTEM 241
- 3.2 INTRODUCTION 242
- Oil Flow 243
- 3.3 STRUCTURE AND OPERATION 244
- Right Turn 247
- Neutral Position 247
- IMPORTANT 249
- 569W687A 256
- 569W688A 256
- 4. HYDRAULIC PUMP 260
- 4.3 STRUCTURE AND OPERATION 261
- 5. HYDRAULIC FILTER 265
- AND TROUBLE SHOOTING 267
- 6.2 STEERING DEVICE 269
- 6.3 PTO SYSTEM 271
- CHAPTER 7 281
- 3. TIGHTENING TORQUE 284
- 4. STRUCTURE AND OPERATION 285
- CHAPTER 7 8454 286
- 4.2 OPERATION 287
- 5.1 DRAINING THE TRANSMISSION 288
- 5.2 SEPARATING PANEL FRAME 289
- Rear Axle Case 294
- Figure Above 295
- Brake Case 295
- Brake Pedal Free Play 296
- 7. SERVICING 297
- Brake Disc Wear 298
- Brake Dise Wear 298
- ELECTRIC SYSTEM 299
- 1. ELECTRONIC INSTRUMENTATION 301
- CHAPTER 8 8454 302
- ELECTRICAL SYSTEM 303
- 2. TROUBLE SHOOTING 304
- 3. SERVICING SPECIFICATIONS 306
- 4. MECHANISM 307
- 4.2 CHARGING SYSTEM 310
- 4.3 PREHEATING SYSTEM 312
- 4.4 FUSE 313
- 4.5 GAUGE AND SENSORS 314
- CABIN SYSTEM 315
- 1. DISASSEMBLY AND ASSEMBLY 317
- CHAPTER 9 8454 318
- Precautions When Assembling 322
- 3. AIRCONDITIONER 323
- 3.2 TROUBLE SHOOTING 327
Related products and manuals for Tractor Cub Cadet 8454
Tractor Cub Cadet RZT L Service Manual
(30 pages)
(30 pages)
Tractor Cub Cadet 5000 Series Service Manual
(96 pages)
(96 pages)
Tractor Cub Cadet 8404 Service Manual
(289 pages)
(289 pages)
Tractor Cub Cadet RANGER RZR User Manual
(20 pages)
(20 pages)
Tractor Cub Cadet 431D User Manual
(15 pages)
(15 pages)
Tractor Cub Cadet 435A Operator's Manual
(24 pages)
(24 pages)
Tractor Cub Cadet 431D User Manual
(4 pages)
(4 pages)
Tractor Cub Cadet GT2000 Operator's Manual
(60 pages)
(60 pages)
Tractor Cub Cadet 642 Operator's Manual
(24 pages)
(24 pages)
Tractor Cub Cadet 640 Operator's Manual
(28 pages)
(28 pages)
Tractor Cub Cadet RZT 54 Operator's Manual
(40 pages)
(40 pages)
Tractor Cub Cadet 430A Operator's Manual
(76 pages)
(76 pages)
Tractor Cub Cadet 640 Operator's Manual
(20 pages)
(20 pages)
Tractor Cub Cadet 7284 User Manual
(89 pages)
Tractor Cub Cadet 641 Operator's Manual
(24 pages)
(24 pages)
Tractor Cub Cadet J466 User Manual
(2 pages)
(2 pages)
Tractor Cub Cadet RZT50 Operator's Manual
(44 pages)
(44 pages)
© 2020, manymanuals.com. All rights reserved. | 4.843 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals