CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019Printed In USAOperatOr’s ManualSafe Operation Practices • Set-Up • Operation • Maintenance •
10 Section 2— ASSembly & Set-Up2. Remove the two shoulder bolts and lock nuts in the seat Figure 3-3 Rotate the sea
11Section 2 — ASSembly & Set-UpConnecting the Battery CablesCALIFORNIA PROPOSITION 65 WARNING! c
Controls & Features412Index PlateDeck Lift PedalDrive PedalReverse PedalThrottle ControlFuel Tank CapSeat Adjustment LeverChoke ControlIgnitionSwi
13Section 4 — controlS & FeatureSPTO (Power Take-Off ) Switch
14 Section 4— controlS & FeatureSChoke ControlThe choke knob controls the position of the engine choke and is located on the RH console. Pull the
Operation515General Safety manual. Learn to operate this machine SAFELY. Do not risk
16 Section 5— operationEngaging the PTO
17Section 5 — operation8. Allow the engine to run for a few minutes at mid-throttle before putting the engine under load.
18 Section 5— operationDriving On Slopeswhere you may operate the tractor safely.WARNING!
Maintenance & Adjustments6Maintenance ScheduleBefore Each useEvery 10 HoursEvery 25 HoursPrior to StoringClean Battery TerminalsP PLube Front Cast
To The Owner12Safe Operation Practices ... 3Assembly & Set-Up ...
Section 6— Maintenance & adjuStMentSb. Using a fuel stabilizer such as STA-BIL® for storage
Section 6 — Maintenance & adjuStMentSLubricationWARNING! brake, st
Section 6— Maintenance & adjuStMentSDeck SpindleGrease fittings can be found on top of each spindle bolt. See
Section 6 — Maintenance & adjuStMentSSetting the Deck WheelsMove the tractor on a firm and level surface, preferably pavement, and proceed as foll
Section 6— Maintenance & adjuStMentSRear Deck RollersThe rear deck rollers can be placed in two positions. To change
Se rvi ce7WARNING! parking brake lever, turn the ignition key to
Section 7— ServiceDeck RemovalRemove the mower deck from the tractor as follows: the e
Section 7 — Service5. After all four cotter pins are secure, slide the deck forward and hook the deck to the U-rod.6.
Section 7— ServiceReplacing the Belt Remove the deck from beneath the tractor, (refer to Deck Removal on page 26).2. Pull the four draw latches up
Section 7 — ServiceSharpening the Blades Remove the deck from beneath the tractor, (refer to Deck Removal on page 26) then gently flip the deck ove
Important Safe Operation Practices23General Operation Read, understand, and follow all instructions on the machine and in the manual(s) before atte
Troubleshooting830Problem Cause RemedyExcessive vibration Cutting blade loose or unbalanced. 2. Damaged or bent cutting blade. Tighten blade
Replacement Parts931Component Part Number and Description
32 Section 9 — Replacement paRtSComponent Part Number and Description
Attachments & Accessories1033Part No. Part
FEDERAL and/or CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONSMTD Consumer Group Inc, the United States Environmen
GDOC-100223 Rev. A
CUB CADET LLCMANUFACTURER’S LIMITED WARRANTY FOR Z-FORCE COMMERCIAL ZERO-TURN COMMERCIAL RIDING MOWERSCub Cadet LLC, P.O. BOX 361131 CLEVELAND, OHIO 4
4 Section 2 — important Safe operation practiceS A missing or damaged discharge cover can cause blade contact or thrown object injuries. Stop
5Section 2 — important Safe operation practiceSChildren Tragic accidents can occur if the operator is not alert to the presence of children. Childr
6 Section 2 — important Safe operation practiceSGeneral Service Never run an engine indoors or in a poorly ventilated area. Engine exhaust contains
7Section 2 — important Safe operation practiceSWARNING! Your Responsibility—Restrict the use of this power machine to persons who read, understand and
8 Section 2 — Safe operation practiceS(OK) (TOO STEEP)USE THIS SLOPE GAUGE TO DETERMINEIF A SLOPE IS TOO STEEP FOR SAFE OPERATION!To check the slope,
Assembly & Set-Up39Contents of Crate
Comments to this Manuals