SNOW THROWERMODELS 850 SWE1130 SWEPRINTED IN U.S.A.FORM NO. 770-10026B.fm(7/00)OPERATOR’S MANUALIMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULL
10WARNING: The temperature of the mufflerand the surrounding areas may exceed150°F. Avoid these areas.• For the most efficient snow removal, remove sn
11• Reconnect the upper shift rod to the lower shift rod by reinserting the hairpin clip removed earlier and sliding the shift rod connector back down
12Figure 11Gear CaseThe gear case is equipped with a grease fitting on the left housing and should be lubricated with Shell Alvania grease EPR00, part
13Figure 13• Remove the six self-tapping screws from the frame cover underneath the snow thrower.• Roll the front and rear auger belts off the auger d
14• Remove the six self-tapping screws from the frame cover underneath the snow thrower.• Remove the click pin that secures the left wheel to the axle
15SECTION 8: TROUBLE SHOOTINGProblem Cause RemedyEngine fails to start 1. Fuel tank empty, or stale fuel.2. Blocked fuel line.3. Choke not in ON posi
16Notes
1721246710914118161315Models 826 SWE & 1130 SWE513317Ref. No.Part No. Part Description1. 618-0123 RH Housing (Incl. Ref. 17, 18)2. 618-0418 LH Hou
18Models 826 SWE & 1130 SWE14102141216320586661606367655758555481711222118411115195271449422736443028324448102338353539943262531404195024373145951
19Models 826 SWE & 1130 SWERef. No.Part No. Part Description1. 684-0008A Shift Arm Assembly2. 710-0262 Carriage Bolt 5/16-18 x 1.5”3. 710-0449 Car
2TABLE OF CONTENTSContent PageImportant Safe Operation Practices...3Assembling Your Sn
20Models 826 SWE & 1130 SWE12345678910111214151316102122232523222618272813303132331618353436373839414042174039292420919
21Models 826 SWE & 1130 SWERef. No.Part No. Part Description1. 712-0116 Lock Jam Nut 3/8-242. 756-0178 Flat Idler 3. 784-5632A Auger Idler Arm4. 7
22Models 826 SWE & 1130 SWE1234567489101112131415161718191916161620212223242526272829303132333435IMPORTANT: For a proper working machine, use Fact
23Models 826 SWE & 1130 SWERef. No.Part No. Part Description1. 710-1652 Hex Washer Screw 1/4-20 x .6252. 731-1324 Belt Cover3. 732-0710 Extension
24Models 826 SWE & 1130 SWE72715284429238111136471150521133337333710913134263130169431734463418196391824403432142032353845403432383220149485749364
25Models 826 SWE & 1130 SWERef. No.Part No. Part Description1. 618-0043 Dogg Assembly: RH2. 618-0044 Dogg Assembly: LH3. 618-0303B Shift Assembly:
26
27
MANUFACTURER’S LIMITED WARRANTY FOR:TWO-YEAR RESIDENTIALONE-YEAR COMMERCIALProper maintenance of your Cub Cadet equipment is the owner’s responsibilit
3SECTION 1: IMPORTANT SAFE OPERATION PRACTICESWARNING: This symbol points out important safety instructions which, if not followed, could endanger th
43. The clutch levers must operate easily in both directions and automatically return to the disengaged position when released. 4. Never operate with
5SECTION 2: ASSEMBLING YOUR SNOW THROWERNOTE: Any reference in this manual to the left or rightside of the snow thrower is observed from theoperator’
6Final AdjustmentsAuger Control AdjustmentCheck the adjustment of the auger control as follows:• Push forward on the auger control until the small rub
7• Recheck the adjustment and repeat adjustment as necessary. • Retighten the jam nut to secure the cable when correct adjustment is reached.NOTE: If
8Electric Chute-Rotation SwitchThe electric chute-rotation switch is located on the leftside of the snow thrower dash panel. See Figure 7.To change th
9WARNING: The electric starter isequipped with a grounded three-wirepower cord and plug and is designed tooperate on 120 volt AC householdcurrent. It
Comments to this Manuals