Cub Cadet CSV 050 Operator's Manual

CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019Printed In USAOp e r a t O r ’s Ma n u a lSafe Operation Practices • Set-Up • Operation • Ma

Controls and Features410Figure 4-1Nozzle Height Adjustment LeverChipper ChuteHose HandleRecoil StarterBagNozzleHose AssemblyNozzle/Hose Vac LeverWARNI

Operation511Starting EnginePull out the choke knob located on the engine. See Fig. 5-1 1. inset.NOTE: Use of the choke may not be necessary if the eng

12 se c t i O n 5— Op e r a t i O nUsing The Hose AssemblyPlace nozzle/hose vac lever in the bottom position on the 1. nozzle to redirect vacuum to t

Maintenance & Adjustments613Figure 6-1MaintenanceGeneral RecommendationsAlways observe safety rules when performing any • maintenance.The warranty

14 se c t i O n 6— Ma i n t e n a n c e & ad j u s t M e n t sRemove and clean the screen by scraping or washing with 6. water. See Fig. 6-3.Rei

Service715Remove the shoulder screws, thrust washers, and bell 5. washers that go through the pivot arms to the front support brace. The front support

16 se c t i O n 7— se r v i c eCarefully tilt and support the unit up to provide access 7. underneath to the nozzle mounting hardware and impeller. R

Troubleshooting817Problem Cause RemedyEngine Fails to start Throttle lever (if equipped) not in correct 1. starting position.Engine switch (if equippe

Engine Operation918-30º -20º10w20w20304020w40, 20w5015w40, 15w5010w4010w30-10º 0º0º 20º 40º 60º 80º 100º10º 20º 30º 40º-20º(ºC)(ºF)12Figure 9-1Fuel Ca

19se c t i O n 9 — Op e r a t i O nCheck Fuel LevelClean around fuel fill before removing cap to fuel.1. Fill tank to approximately 1-inch below lowe

Customer SupportIf you have difficulty assembling this product or have any questions regarding the controls, operation, or maintenance of this machine

Engine Maintenance1020WARNING: Shut off the engine before performing any maintenance. To prevent accidental start-up, disconnect the spark plug boot.I

21se c t i O n 10 — en g i n e Ma i n t e n a n c e Oil ServiceCheck oil level regularly.• Be sure correct oil level is maintained. Check every fiv

22 se c t i O n 10— en g i n e Ma i n t e n a n c eElectrode0.030 in.Figure 10-43. Measure the plug gap with a feeler gauge. Correct as necessary b

23se c t i O n 10 — en g i n e Ma i n t e n a n c e Fuel Filter ServiceThe fuel filter cannot be cleaned and must be replaced once a year or every

24Model CSV 0505239414057565554534743354245148504950937364201617181975114123434610381346374431332420152720255030292122112852826322823

25Model CSV 050Ref No.Part Number Description1 936-0314 Thrust Washer.375 ID x.70 OD2 749-04172-0637 Upper Handle3 720-0279 Knob4 710-0599 Screw, 1/4-

263830404243BBAA412945431097564430464916191812141726273228353437363911111444844215132324222120258313347Model CSV 050

27Model CSV 050Ref No.Part Number Description1 664-04040 Bag Assembly2 681-0154-0637 Screen Assembly3 710-1054 Hex Screw 5/16-24 x 1.0 4 981-0490 Chip

28Engine Model - 1P70C0292745101161213152930202112242517262814313181998716232232

29Engine Model - 1P70C0Ref No.Part Number Description1. 951-10368 Fuel Tank 2. 951-10369 Flywheel Shroud 3. 951-10335 Rubber Fuel Tank Mounting Wash

Important Safe Operation Practices23TrainingRead, understand, and follow all instructions on the 1. machine and in the manual(s) before attempting to

Cub Cadet LLC (Cub Cadet), the California Air Resources Board (CARB) and the United States Environment Protection Agency (U. S. EPA) Emission Control

(4) Repair or replacement of any warranted part under the warranty provisions of this article must be performed at no charge to the owner at a warra

GDOC-100181 Cub Cadet LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019; Phone: 1-877-282-8684MTD Canada Limited - KITCHENER, ON N2G 4J1; Phone 1-800

4 se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sSafe Handling of Gasoline:To avoid personal injury or property damage

5se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sMaintenance & StorageNever tamper with safety devices. Check their

6 se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sSafety SymbolsThis page depicts and describes safety symbols that may

Assembly & Set-Up37AssemblyNOTE: This unit is shipped without gasoline or oil in the engine. Fill up gasoline and oil as instructed in the accompa

8 se c t i O n 3 — as s e M b l y & se t -upPull spring loaded pin out on the base and align pin with 2. the first hole (closest to the end of t

9se c t i O n 3 — as s e M b l y & se t -upAdjustmentsNozzle HeightThe nozzle can be adjusted to any six positions, ranging from 5/8” to 4 1/8”