Cub Cadet 770-10538 31AH4Q3G100 Operator's Manual

Browse online or download Operator's Manual for Snow throwers Cub Cadet 770-10538 31AH4Q3G100. Cub Cadet 770-10538 31AH4Q3G100 Operator`s manual [en] User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 28
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
SNOW
THROWER
MODEL
31AH4Q3G100
4-Wheel Drive
OPERATOR’S MANUAL
PRINTED IN U.S.A.
FORM NO.
770-10538.fm
(5/01)
IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY
CUB CADET CORP. P.O. BOX 368023 CLEVELAND, OHIO 44136-9722
Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-
covered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting
applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator.
In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have
similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine authorized
service dealer or contact the service department, P.O. Box 368023 Cleveland, Ohio 44136-9722.
Page view 0
1 2 3 4 5 6 ... 27 28

Summary of Contents

Page 1 - OPERATOR’S MANUAL

SNOW THROWERMODEL31AH4Q3G1004-Wheel DriveOPERATOR’S MANUALPRINTED IN U.S.A.FORM NO. 770-10538.fm(5/01)IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CA

Page 2 - CALLING CUSTOMER SUPPORT

10NOTE: Keep it in a safe place. Engine will not startwithout ignition key.Wipe all snow and moisture from the carburetor cover in the area of the co

Page 3 - Operation

11Figure 9Shift Rod AdjustmentTo adjust the shift rod, proceed as follows:• Remove the hairpin clip and slide the shift rod connector up, to separate

Page 4 - Maintenance And Storage

12Electric Chute-Rotation MotorThe gear on the electric chute-rotation motor and the base of the discharge chute itself should be lubed with multi-pur

Page 5 - Assembly

13 Figure 13• Remove the three hex nuts and lock washers which attach the auger housing assembly to the frame assembly on each side. See Figure 14. WA

Page 6 - Final Adjustments

14• Remove the plastic belt cover on the front of the engine by removing the two self-tapping screws.• Tip the snow thrower up and forward, so that it

Page 7 - Tire Pressure

15• Reassemble new friction wheel rubber to the friction wheel assembly, tightening the six screws in rotation and with equal force.• Insert the pin f

Page 8

16SECTION 8: TROUBLE SHOOTING GUIDENOTE: For repairs beyond the minor adjustments listed above, please contact your local Cub Cadet dealer.Trouble Po

Page 9 - To Stop Engine

17Model H4Q3G22212019117141486813613471581416126981416223102318Ref. No.Part No. Description1. 710-0459A Special Hex Screw: 3/8-24 x 1.5”2. 710-0599 TT

Page 10 - IMPORTANT:

18Model H4Q3G42524647504954514856414355455343334457282993052520171413181811327183391023167102322622638593660191246222221322353415212811212640832313322

Page 11 - Lubrication

19Ref. No.Part No. Description1. 05931A Bearing Housing 2. 684-0065 Impeller Assy. 12” dia.3. 705-5226 Chute Reinforcement4. 710-0451 Carriage Bolt 5/

Page 12 - Belt Removal And Replacement

2TABLE OF CONTENTSContent PageImportant Safe Operation Practices...3Assembling Your Sn

Page 13 - Drive Belt

20Model H4Q3G 5657594443421348375013544837711499152739252321831244528172910644134347202382514233934411115532185162330111251134837531313383316402216333

Page 14

21Model H4Q3G37. 738-0924 Shoulder Screw38. 741-0598 Hex Flange Bearing39. 741-0600 Ball Bearing40. 741-0701 Flange Bushing41. 741-1111 Hex Flange Bea

Page 15 - Off-season Storage

22Model H4Q3G1134811832620251422296121623212321231315524197102728293031

Page 16

23Model H4Q3GRef. No.Part No. Description1. 05896A Idler Bracket2. 710-0230 Hex Bolt 1/4-28 x 0.5” Gr.53. 710-0627 Hex Scr w/ Patch: 5/16-24 x 0.75” 4

Page 17 - Model H4Q3G

24Model H4Q3G14102141216320586661606367655758555481711222118411115195271423383535399432625314041950243731459514046475359296869692782707272732768717427

Page 18

25Model H4Q3GRef. No.Part No. Part Description1. 684-0008A Shift Arm Assembly2. 710-0262 Carriage Bolt 5/16-18 x 1.5”3. 710-0449 Carriage Bolt 5/16-18

Page 19

26Notes

Page 21

MANUFACTURER’S LIMITED WARRANTY FOR:TWO-YEAR RESIDENTIALONE-YEAR COMMERCIALProper maintenance of your Cub Cadet equipment is the owner’s responsibilit

Page 22

3SECTION 1: IMPORTANT SAFE OPERATION PRACTICESWARNING: This symbol points out important safety instructions which, if not followed, could endanger th

Page 23

43. The clutch levers must operate easily in both directions and automatically return to the disengaged position when released. 4. Never operate with

Page 24

5SECTION 2: ASSEMBLING YOUR SNOW THROWERNOTE: Any reference in this manual to the left or rightside of the snow thrower is observed from theoperator’

Page 25

6Figure 5Final AdjustmentsAuger Control AdjustmentCheck the adjustment of the auger control as follows:• Push forward on the auger control until the s

Page 26

7Figure 7• Retighten the hex nuts loosened earlier.• Repeat this adjustment on the skid shoe found on the opposite side of the snow thrower.Tire Press

Page 27

8Auger Drive ControlThe auger drive control is located on the left handle. Squeeze the control grip to engage the augers. Release to stop the snow thr

Page 28

9WARNING: Use extreme care whenhandling gasoline. Gasoline is extremelyflammable and the vapors are explosive.Never fuel machine indoors or while thee

Comments to this Manuals

No comments