Cub Cadet 190-002 Operator's Manual

Browse online or download Operator's Manual for Mini tillers Cub Cadet 190-002. Cub Cadet 190-002 Operator`s manual User Manual

  • Download
  • Add to my manuals
  • Print

Summary of Contents

Page 1 - Operator’s Manual

IMPORTANT: Read safety rules and instructions carefully before operating equipment.CUB CADET CORP. P.O. BOX 368023 CLEVELAND, OHIO 44136-9722Model 190

Page 2 - CALLING WARRANTY SERVICE

10IMPORTANT: If working on or with the battery for any reason, disconnect the NEGATIVE (Black) wire from it’s terminal first, followed by the POSITIVE

Page 3 - General Operation

11• To mark the hole to ensure proper centering of the new hole to be drilled, place the pointed end of a center punch on the cross hairs of new hole

Page 4 - Children

12SECTION 7: MOUNTING THE TILLERInstalling the Attachment HitchThe attachment hitch, which has the electric lift cylinder attached to it, attaches to

Page 5 - Your Responsibility

13Attaching the Hydraulic Pump AssemblyTo mount the hydraulic pump assembly to the tractor, make certain that it is placed under the center of the tra

Page 6 - SECTION 2: SLOPE GAUGE

14SECTION 8: KNOW THE TILLERFigure 14Lift SwitchThe lift switch is located on the right side of the steering wheel on the dash panel and is used to r

Page 7 - SECTION 4: LOOSE PARTS

15R is the reverse tilling position. The tine direction lever is pushed toward the back of the machine, or away from the operator to start the tines i

Page 8 - Hydraulic Fluid

16Engaging the Tiller NOTE: Refer to the tractor’s operator’s manual forinformation concerning starting and stopping thetractor, and location and pro

Page 9 - Installing the Lift Switch

17For shallow tilling, drop the roller to its lowest position by putting the locking rod into the highest hole of the adjustment bar. For deeper tilli

Page 10 - Installing the Shoulder Bolts

18If the object does not dislodge using this method and the tines continue to not spin:• Shut off the PTO immediately, shift the tine direction lever

Page 11 - (Drill Here)

19With the new filter in place, remove all tools used to change the filter from the tiller: • Start the tiller in motion for about one minute in order

Page 12 - Attaching the Tiller Assembly

2TABLE OF CONTENTSContent PageImportant Safe Operation Practices... 3Slope Gauge ...

Page 13 - Installing the PTO Drive Belt

20Replace only one tine at a time. This will help to insure the correct positioning of the tines as they are mounted on the tine assembly. When instal

Page 14 - SECTION 8: KNOW THE TILLER

21SECTION 11: STORAGENOTE: Before removing the tiller attachment forstorage, perform all lubrication maintenance as outlinedin the Maintenance secti

Page 15

22Figure 25• Holding the hitch latches up will allow the tractor, with the attachment hitch still mounted, to be pushed away from the tiller with the

Page 16 - Using the Roller

23SECTION 13: TEMPLATESDash Panel TemplateInstructions:1. Carefully cut the template along the dotted lines only.2. Tape the template into position o

Page 18 - SECTION 10: MAINTENANCE

25Rear Frame TemplateExisting HoleInstructions:1. Carefully cut the template along the dotted lines only.2. Continue following instruction given on pa

Page 21 - SECTION 11: STORAGE

MANUFACTURER’S LIMITED WARRANTY FOR:TWO-YEAR RESIDENTIALONE-YEAR COMMERCIALProper maintenance of your Cub Cadet equipment is the owner’s responsibilit

Page 22 - SECTION 12: TROUBLE SHOOTING

3SECTION 1: IMPORTANT SAFE OPERATION PRACTICESWARNING: This symbol points out important safety instructions which, if not followed, could endanger th

Page 23 - SECTION 13: TEMPLATES

4parking brake, turn engine off and remove key before dismounting.• Disengage the PTO, stop the engine and wait until the tiller comes to a complete s

Page 24

5• Never remove gas cap or add fuel while the engine is hot or running. Allow engine to cool at least two minutes before refueling.• Never over fill f

Page 25 - Rear Frame Template

6SECTION 2: SLOPE GAUGE

Page 26

7SECTION 3: TO THE OWNERModel 190-002-100, 30-inch hydraulic tiller attachment is designed for use on Series 2000 Lawn Tractors with 23” rear tires o

Page 27

8To connect the hydraulic hoses to the hydraulic pump assembly:• Locate both male hydraulic fittings on the hydraulic pump. Notice that the fittings a

Page 28

9SECTION 6: PREPARING THE TRACTORNOTE: References to LEFT and RIGHT indicate the leftand right sides of the tractor and tiller attachment whenfacing

Comments to this Manuals

No comments