CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019Printed In USAOperatOr’s ManualSafe Operation Practices • Set-Up • Operation • Maintenance •
10 Section 3— ASSembly & Set-UpAdjustmentsSkid ShoesThe snow thrower skid shoes are adjusted at the factory for shipping purposes. Adjust them dow
Controls and Features411Snow thrower controls and features are described below and illustrated in Figure 4-1. Shift LeverThe shift lever is located in
12 Section 4 — controlS and FeatureSAuger ControlThe auger control is located on the left handle. Squeeze the control grip against the handle to engag
13Section 4 — controlS and FeatureSTrack Lock LeverThe track lock lever is located on the right side of the snow thrower and is used to select the pos
Operation514Starting and Stopping the EngineRefer to the Engine Operator’s Manual packed with your snow thrower for instructions on starting and stopp
Maintenance & Adjustments615MaintenanceEngineRefer to the Engine Operator’s Manual.Shave Plate and Skid ShoesThe shave plate and skid shoes on the
16 Section 6 — Maintenance & adjuStMentSLubricationWheelsAt least once a season, remove both wheels. Clean and coat the axles with a multipurpose
17Section 6 — Maintenance & adjuStMentSAdjustmentsShift RodIf the full range of speeds (forward and reverse) cannot be achieved, adjust the shift
18 Section 6 — Maintenance & adjuStMentS3. Position the bracket upward to provide more slack (or downward to increase cable tension). 4. Retight
Se rvice719Belt ReplacementAuger BeltTo remove and replace your snow thrower’s auger belt, proceed as follows:1. Allow the engine to run until it is
Product Registration and Customer SupportPlease register your product on our website, www.cubcadet.com.If you have difficulty assembling this product
20 Section 7— Service5. Carefully pivot the snow thrower up and forward so that it rests on the auger housing. 6. Remove the frame cover from the un
Troubleshooting821Problem Cause RemedyEngine fails to start 1. Fuel tank empty, or stale fuel. 2. Blocked fuel line.3. Choke not in the RUN positio
Replacement Parts922Component Part Number and Description954-04195A Auger Drive Belt954-05019 Track Drive Belt684-04153C Friction Wheel Assembly935
Attachments & Accessories1023The following attachments and accessories are available for your Cub Cadet snow thrower. See your Cub Cadet dealer or
Cub Cadet LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019; Phone: 1-877-282-8684 MTD Canada Limited - KITCHENER, ON N2G 4J1; Phone 1-800-
Important Safe Operation Practices23Training1. Read, understand, and follow all instructions on the machine and in the manual(s) before attempting to
4 Section 2 — important Safe operation practiceSSafe Handling of GasolineTo avoid personal injury or property damage use extreme care in handling gaso
5Section 2 — important Safe operation practiceSClearing a Clogged Discharge ChuteHand contact with the rotating impeller inside the discharge chute is
6 Section 2 — important Safe operation practiceSSafety SymbolsThis page depicts and describes safety symbols that may appear on this product. Read, u
Assembly & Set-Up37Contents of Carton• Snow Thrower • Replacement Auger Shear Pins • Chute Assembly• Flex Shaft • Engine Manual • Product Re
8 Section 3— ASSembly & Set-Up2. Place chute assembly onto chute base.3. Secure chute control head to chute support bracket with the lock nuts a
9Section 3 — ASSembly & Set-UpSet-UpShear Pins StorageReplacement auger shear pins and bow tie cotter pins are included with your snow thrower. St
Comments to this Manuals