Cub Cadet 20HP 53AB5E6V150 Service Manual

Browse online or download Service Manual for Lawnmowers Cub Cadet 20HP 53AB5E6V150. Cub Cadet 20HP 53AB5E6V150 Service manual User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 32
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
Hydrostatic Zero-Turn
Commercial Riding Mower
Professional Turf Equipment
OPERATOR’S AND SERVICE MANUAL
MODEL
19HP Tank, 53BB5DAV150
20HP Tank, 53AB5E6V150
23HP Tank, 53BB5DBW15
0
24HP Tank, 53AB5ETW150
25HP Tank, 53AB5D8X150
27HP Tank, 53AB5BDX150
28HP Tank, 53AB5FEZ150
Page view 0
1 2 3 4 5 6 ... 31 32

Summary of Contents

Page 1 - Commercial Riding Mower

Hydrostatic Zero-TurnCommercial Riding MowerProfessional Turf EquipmentOPERATOR’S AND SERVICE MANUALMODEL19HP Tank, 53BB5DAV15020HP Tank, 53AB5E6V1502

Page 2 - TABLE OF CONTENTS

104.Electric Blade Clutch Switch: (See Figure 1.) Located on the right side of the mower beside the ignition switch. This is an “on/off” push pull swi

Page 3 - CAUTION:

11C.Initial Adjustments1. Check the fluid levels and tires:Note: These checks should be made daily, before starting the engine.a.Fuel: Using a good gr

Page 4 - SAFETY PRECAUTIONS

12clockwise a few turns. Adjust both front and rear Deck links as necessary. Retighten nuts.f. Raise the mowing deck to the transport position using t

Page 5 - C. When Mowing

13run. Turn off the PTO by pushing the control switch down.h. To drive in the FORWARD direction:1. Set the engine speed to 2000 to 2500 rpm (refer to

Page 6 - DO NOT OPERATE

14e. Push the throttle control to a position a third of the way between slow and fast.f. Insert the key in the ignition and start switch and turn the

Page 7 - SPECIFICATIONS

15d. Detach the mower drive belt.e. Remove six linchpins (See Fig. 6) (4) from the deck and (2) from the front of the mower. Remove the linchpins on t

Page 8 - OPERATING INSTRUCTIONS

16e. Pull the tensioner pulley away from the belt and remove the PTO belt then remove the blade drive belt.f. Reverse the process to install the belt.

Page 9 - B.Controls

17caps and drain oil from both left and right pumps. Replace and retighten nuts.j. Coat new filter seal with oil before installa-tion. Install new hyd

Page 10 - Fuel Shutoff Valve

18other electrical components. This is a stan-dard plug-in type automotive fuse rated at 7.5 amp.7.Safety Switches: There are five safety switches in

Page 11 - C.Initial Adjustments

19does not stop, the seat switch must be replaced. With both steering levers folded out in the neutral position, the parking brake engaged and the bla

Page 12 - WARNING:

2TABLE OF CONTENTSForeword. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Page 13

20d. Loosen jam nuts on both ends of rod con-nectors. See Control Assembly in the Illus-trated Parts Book (ONLY if mower creeps.)e. Start unit and pus

Page 14 - MAINTENANCE AND

213.Hydrostatic Pumps and Motors: The pumps are the hardest-working components in the hydraulic system. They are in operation all the time the engine

Page 15

22into an approved fuel container. Open the fuel tank shutoff valve and drain the fuel tank and line into the approved container. Replace the fuel lin

Page 16

23.OIL CHARTApply a few drops of SAE 20W-50 engine oil or use a spray lubricant. Apply the oil to both sides of pivot points. Wipe off any excess. Sta

Page 17 - Warning:

24Performance AdjustmentsA. High Speed Tracking AdjustmentIf mower tracks to one side with both lap bars in fully forward position:1. Check air pressu

Page 18

25f. Repeat as required to obtain proper throt-tle adjustment.g. Verify proper throttle adjustment by check-ing RPM readings as outlined above.C. Deck

Page 19

26F. Deck leveling Procedure1. Park the mower on a flat paved surface, engage the parking brake, shut off the engine, remove the key from the ignition

Page 21 - Contaminants

28MAINTENANCE RECORDDATE WORK PERFORMED DATE WORK PERFORMED

Page 22 - MAINTENANCE SCHEDULE

29MAINTENANCE RECORDDATE WORK PERFORMED DATE WORK PERFORMED

Page 23 - LUBRICATION CHART

3FORWARDThe Tank Hydrostatic Zero-Turn Commercial Riding Mower provides superb maneuverability,mid-mount cutting capability for professional landscape

Page 24 - Performance Adjustments

30MAINTENANCE RECORDDATE WORK PERFORMED DATE WORK PERFORMED

Page 25 - E. Lap Bar Adjustment

MAINTENANCE RECORDDATE WORK PERFORMED DATE WORK PERFORMED

Page 26 - F. Deck leveling Procedure

MANUFACTURER’S LIMITED WARRANTY - TURF EQUIPMENTThis warranty is specific to the product manual to which it is attached.For a complete list of product

Page 27 - WIRING DIAGRAM

4GENERAL SAFETYOPERATIONSA. DANGER1. Do not operate machine in confined areas where exhaust gases can accumulate.2. Do not operate machine without mow

Page 28 - MAINTENANCE RECORD

511. When looking for oil leaks, never run your hand over hydraulic hoses, lines or fittings. Never tighten or adjust hydraulic hoses, lines or fittin

Page 29

6SAFETY DECALS AND LABELSWARNINGSHIELD MISSINGDO NOT OPERATEPart Number: 00030635Part Number: 01003858Do not put hands or feetunder or into mower when

Page 30

7SPECIFICATIONSEngine: 19HP Kawasaki, 20HP Honda, 24HP Honda, 23HP Kawasaki, 25HP Kawasaki, 27HP Kohler, 28HP GeneracType: Vertical air cooled V-Twin

Page 31

8OPERATING INSTRUCTIONSA.General1. When Mowing:a. Keep adults, children, and pets away from the area to be mowed.b. When operating this mower, in the

Page 32 - Cleveland, Ohio 44136

9c. Avoid turning when going downhill, traction is at a minimum going downhill.d. Do not operate with discharge side of the mower toward streets, buil

Comments to this Manuals

No comments